{"title":"Bosch Smart System E-Bike Tuning kits","description":"\u003cp\u003eAll tuning kits in this collection will fit your e-bike with a Bosch Smart System motor if the speed sensor is wired to the engine.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eImportant:\u003c\/strong\u003e Please ensure whether your e-bike is equipped with a rim magnet. Only \u003cstrong\u003e\u003ca href=\"https:\/\/www.twowheelsempire.com\/products\/speedbox-1-2-for-bosch-smart-system-rim-magnet\" target=\"_blank\"\u003eSpeedbox 1.2\u003c\/a\u003e\u003c\/strong\u003e and \u003cstrong\u003e\u003ca href=\"https:\/\/www.twowheelsempire.com\/collections\/emtb-tuning-kits\/products\/speedbox-1-2-b-tuning-for-bosch-smart-system-rim-magnet\" target=\"_blank\"\u003eSpeedbox 1.2B Tuning\u003c\/a\u003e \u003c\/strong\u003ekits are compatible with e-bikes that have a rim magnet \u003cspan data-mce-fragment=\"1\"\u003eon a rear wheel valve\u003c\/span\u003e.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eImportant:\u003c\/strong\u003e None of these tuning kits work if the e-bike is equipped with the Bosch ABS System and\/or Enviolo Automatiq.\u003c\/p\u003e\n\u003cp\u003eIf no rim magnet is present, all other tuning kits in this collection will fit your e-bike with a \u003cstrong\u003eBosch Smart System\u003c\/strong\u003e motor.\u003c\/p\u003e\n\u003cp\u003eIf your e-bike is equipped with a non-Smart System motor, you should consider checking out \u003ca href=\"https:\/\/www.twowheelsempire.com\/collections\/bosch-motor-e-bike-tuning-kits\" target=\"_blank\"\u003e\u003cstrong\u003eBosch Tuning kits\u003c\/strong\u003e\u003c\/a\u003e\u003c\/p\u003e","products":[{"product_id":"speedbox-1-0-for-bosch-smart-system","title":"SpeedBox 1.1 for Bosch Smart System","description":"\u003ch3\u003eWhat does this Tuning Kit do?\u003c\/h3\u003e\n\u003cp\u003eSpeedBox 1.1 enables you to \u003cb\u003esuppress the speed limiter\u003c\/b\u003e on your e-bike. When in use, the display shows the real speed up to 25 km\/h.\u003c\/p\u003e\n\u003ch3\u003eHow does SpeedBox 1.1 work?\u003c\/h3\u003e\n\u003cp\u003eThe tuning kit manipulates the speed signal without altering the motor's power relative to pedaling speed. This guarantees a smooth motor control without speed limit interruptions. Depending on a tuning kit, some determine when assistance stops, while others remove the restriction entirely for continuous support. However, the achievable speed mostly depends on the eBike model. Achievable speed can be calculated using a simple formula: \u003cbr\u003e\u003cbr\u003eSpeed = Cadence [rpm] * Wheel circumference [mm] * Front Chainring Teeth \/ Rear Chainring Teeth * 60 [min\/h] \/ 1.000.000 [mm\/km] \u003cbr\u003e\u003cbr\u003eThis tuning chip is also very easy to control. \u003cbr\u003e\u003cb\u003eActivate\/deactivate the tuning before the ride (when the e-bike is standing still), not during riding!\u003c\/b\u003e \u003cbr\u003eActivation: one short press of WALK button or + - + - or - + - + (sequence requires to press it all quickly) \u003cbr\u003eIndication: 3.5 kph (2.2 mph) on your display = SpeedBox activated \u003cbr\u003e\u003cbr\u003eAfter the activation you can reach maximum speed - 22 mph (35 km\/h). Indication of tuning activation 2.2 mph (3.5 km\/h). However we recommend not to exceed 35 km\/h. \u003cbr\u003e\u003cbr\u003eIf you want to see correct speed and all riding data during your ride, we recommend choosing \u003cb\u003e\u003ca href=\"https:\/\/www.twowheelsempire.com\/products\/speedbox-1-0-b-tuning-for-bosch-smart-system\" target=\"_blank\"\u003e SpeedBox 1.1 B.Tuning for Bosch Smart System \u003c\/a\u003e\u003c\/b\u003e - you can see the real values in our SpeedBox App – right on the display of your phone. \u003cbr\u003e\u003cbr\u003eTo deactivate the tuning kit, press the WALK \/ + - + - buttons again. Your e-bike display will show a value of 2.2 mph (3.5 km\/h) and the speed limit will be reset to 16mph (25 km\/h). Your e-bike will then work the same as before the chip installation. \u003cbr\u003e\u003cbr\u003eAfter finishing the ride, leave the e-bike on for a while until SpeedBox finishes the \"countdown\" process (the ride time will continue on the display until it stops and shows the correct distance traveled) to prevent tuning detection on your e-bike. Do not remove the display to lock the e-bike until SpeedBox finishes the \"countdown\" process.\u003cbr\u003e\u003cbr\u003ePlease disable automatic updates in the eBike Flow App. And do not us flow app together with tuning kit.\u003c\/p\u003e\n\u003ch3\u003eWhich Speedbox Tuning Kit do I need?\u003c\/h3\u003e\n\u003cp\u003eThe tuning chip for e-bikes with the newest Bosch Gen4 motor with Smart System. \u003cbr\u003e\u003cbr\u003e\u003cb\u003eCompatible with:\u003c\/b\u003e\u003cbr\u003e- All the Smart System displays \u003cbr\u003e- All the Smart System motors \u003cbr\u003e- Not compatible with e-bikes that have a magnet attached to a valve (Bosch Rim Magnet) and ABS system.\u003cbr\u003e-The module now supports drive unit software version up to 20.27.0\u003cbr\u003e\u003cbr\u003eIf your e-bike has Bosch Gen4, Gen3 or Gen2 without Smart System, we recommend \u003cb\u003e\u003ca href=\"https:\/\/www.twowheelsempire.com\/products\/speedbox-3-0-ebike-tuning-kit-for-bosch-2014-2022-motor\" target=\"_blank\"\u003e SpeedBox 3.0 (incl. Gen4)\u003c\/a\u003e\u003c\/b\u003e or \u003cb\u003e\u003ca href=\"https:\/\/www.twowheelsempire.com\/products\/speedbox-b-tuning-3-0-for-all-2014-2020-bosch-motors\" target=\"_blank\"\u003e SpeedBox 3.0 B.Tuning (incl. Gen4) \u003c\/a\u003e\u003c\/b\u003e\u003cbr\u003eIf your ebike has Bosch Smart system with rim magnet, you would need \u003cb\u003e\u003ca href=\"https:\/\/www.twowheelsempire.com\/products\/speedbox-1-2-b-tuning-for-bosch-smart-system-rim-magnet\"\u003eSpeedBox 1.2 B.Tuning for Bosch (Smart System + Rim Magnet)\u003c\/a\u003e\u003c\/b\u003e or \u003cb\u003e\u003ca href=\"https:\/\/www.twowheelsempire.com\/collections\/all\/products\/speedbox-1-2-for-bosch-smart-system-rim-magnet\"\u003e SpeedBox 1.2 for Bosch (Smart System + Rim Magnet)\u003c\/a\u003e\u003c\/b\u003e\u003c\/p\u003e\n\u003ch3\u003eHow to install this Tuning kit?\u003c\/h3\u003e\n\u003cp\u003eWe use original connectors for the production of SpeedBox chips ensuring that the installation process is very simple and the chip is connected properly. We have also prepared detailed instructions and videos to make installation easy for you. Disassembly of the tuning chip is just as easy. If you have any troubles with installation or disassembly, do not hesitate to contact us. \u003cbr\u003eIf you are planning to install SpeedBox on a brand-new bike, make sure you ride it for at least 1 km before the chip is activated. \u003cbr\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cdiv class=\"text-center\"\u003e\n\u003cb\u003eImportant:\u003c\/b\u003e\u003cbr\u003eConnect the male - female connectors in the direction of the lock. Do not rotate the connectors during connection! \u003cbr\u003e\u003cbr\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0051\/1515\/0434\/files\/speedbox-connection.png?v=1670584224\" alt=\"\"\u003e \u003cbr\u003e\n\u003c\/div\u003e\n\u003cp\u003e\u003cbr\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp class=\"text-center fw-bold\"\u003eInstallation Guide:\u003c\/p\u003e\n\u003cdiv style=\"padding-bottom: 56.25%; position: relative; display: block; width: 100%;\"\u003e\u003ciframe width=\"100%\" height=\"100%\" src=\"https:\/\/www.youtube.com\/embed\/eaerAdy2P7o?si=dD2Q7r9VlRuA43CH\" style=\"position: absolute; top: 0; left: 0;\"\u003e\n    \u003c\/iframe\u003e\u003c\/div\u003e\n\u003ch3\u003eImportant legal note!\u003c\/h3\u003e\n\u003cp\u003ePlease note that the operation of this type of modified electric bikes on public roads may be against the law in some countries. The manufacturer takes no responsibility for damages resulting from the use SpeedBox products. Electric bikes equipped with SpeedBox products are not allowed to be used on public roads, cycling paths and public places. Electric bikes equipped with SpeedBox products can be used exclusively on private property and entirely at one’s own risk. \u003cbr\u003e\u003cbr\u003eThe use of SpeedBox may void the warranty of your ebike. \u003cbr\u003e\u003cbr\u003eWe strongly recommend using other safety features and protective gear to prevent injuries in higher speeds. \u003cbr\u003e\u003cbr\u003eSpeedBox Products are thoroughly tested and we stand by their quality. SpeedBox provide Life Long warranty to all their Products! \u003cbr\u003e\u003cbr\u003eIf You have any questions, please do not hesitate to contact us. Thank you for looking! Two Wheels Empire Team\u003c\/p\u003e","brand":"Speedbox","offers":[{"title":"Default Title","offer_id":39730917310598,"sku":"SB11_SS","price":229.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0051\/1515\/0434\/files\/speedbox-1-1-for-bosch-smart-system-sb11-ss-1145467221.jpg?v=1741936377"},{"product_id":"speedbox-1-0-b-tuning-for-bosch-smart-system","title":"SpeedBox 1.1 B.Tuning for Bosch Smart System","description":"\u003ch3\u003eWhat does this Tuning Kit do?\u003c\/h3\u003e\n\u003cp\u003eSpeedBox 1.1 enables you to \u003cb\u003esuppress the speed limiter\u003c\/b\u003e on your e-bike. When in use, the display shows the real speed up to 25 km\/h. \u003cbr\u003e\u003cbr\u003eWith B.Tuning version you can see the real values in our SpeedBox App – right on the display of your phone.\u003c\/p\u003e\n\u003ch3\u003eHow does SpeedBox 1.1 B.Tuning work?\u003c\/h3\u003e\n\u003cp\u003eThe tuning kit manipulates the speed signal without altering the motor's power relative to pedaling speed. This guarantees a smooth motor control without speed limit interruptions. Depending on a tuning kit, some determine when assistance stops, while others remove the restriction entirely for continuous support. However, the achievable speed mostly depends on the eBike model. Achievable speed can be calculated using a simple formula: \u003cbr\u003e\u003cbr\u003eSpeed = Cadence [rpm] * Wheel circumference [mm] * Front Chainring Teeth \/ Rear Chainring Teeth * 60 [min\/h] \/ 1.000.000 [mm\/km] \u003cbr\u003e\u003cbr\u003eThis tuning chip is also very easy to control. \u003cbr\u003e\u003cbr\u003e\u003cb\u003eActivate\/deactivate the tuning before the ride (when the e-bike is standing still), not during riding!\u003c\/b\u003e \u003cbr\u003eActivation: one short press of WALK button or + - + - or - + - + (sequence requires to press it all quickly) \u003cbr\u003eIndication: 3.5 kph (2.2 mph) on your display = SpeedBox activated \u003cbr\u003e\u003cbr\u003eAfter the activation you can reach maximum speed - 22 mph (35 km\/h). Indication of tuning activation 2.2 mph (3.5 km\/h). However we recommend not to exceed 35 km\/h. \u003cbr\u003e\u003cbr\u003eThe tuning with Bluetooth technology and mobile app for your e-bike with Bosch Gen4 motor and Smart System. Enjoy your unlimited ride and all the great functions that our SpeedBox App has to offer. \u003cbr\u003eSpeedBox 1.1 B.Tuning for Bosch brings a unique connection of e-bike and mobile phone and suppresses the speed limiter on your e-bike. \u003cbr\u003eThe actual speed and other riding data will be displayed correctly in our SpeedBox App - right on the display of your phone. \u003cbr\u003e\u003cbr\u003eTo deactivate the tuning kit, press the WALK \/ + - + - buttons again. Your e-bike display will show a value of 2.2 mph (3.5 km\/h) and the speed limit will be reset to 16mph (25 km\/h). Your e-bike will then work the same as before the chip installation. \u003cbr\u003e\u003cbr\u003eAfter finishing the ride, leave the e-bike on for a while until SpeedBox finishes the \"countdown\" process (the ride time will continue on the display until it stops and shows the correct distance traveled) to prevent tuning detection on your e-bike. Do not remove the display to lock the e-bike until SpeedBox finishes the \"countdown\" process.\u003cbr\u003e\u003cbr\u003ePlease disable automatic updates in the eBike Flow App. And do not us flow app together with tuning kit.\u003c\/p\u003e\n\u003ch3\u003eWhich Speedbox Tuning Kit do I need?\u003c\/h3\u003e\n\u003cp\u003eThe tuning chip for e-bikes with the newest Bosch Gen4 motor with Smart System. \u003cbr\u003e\u003cbr\u003e\u003cb\u003eCompatible with:\u003c\/b\u003e\u003cbr\u003e- All the Smart System displays \u003cbr\u003e- All the Smart System motors \u003cbr\u003e- SpeedBox App\u003cbr\u003e\u003cb\u003e- Not compatible with e-bikes that have a magnet attached to a valve (Bosch Rim Magnet).\u003c\/b\u003e \u003cbr\u003e\u003cbr\u003e\u003cb\u003eNot compatible with with e-bikes with Bosch ABS system and ABS system\u003c\/b\u003e \u003cbr\u003e\u003cbr\u003eThe module now supports drive unit software version up to 20.27.0 \u003cbr\u003e\u003cbr\u003eIn case of updating the software of your e-bike, uninstall SpeedBox from the e-bike first, update the software and reinstall SpeedBox. \u003cbr\u003e\u003cbr\u003eIf your e-bike has Bosch Gen4, Gen3 or Gen2 without Smart System, we recommend \u003cb\u003e\u003ca href=\"https:\/\/www.twowheelsempire.com\/products\/speedbox-3-0-ebike-tuning-kit-for-bosch-2014-2022-motor\" target=\"_blank\"\u003e SpeedBox 3.0 (incl. Gen4)\u003c\/a\u003e\u003c\/b\u003e or \u003cb\u003e\u003ca href=\"https:\/\/www.twowheelsempire.com\/products\/speedbox-b-tuning-3-0-for-all-2014-2020-bosch-motors\" target=\"_blank\"\u003e SpeedBox 3.0 B.Tuning (incl. Gen4) \u003c\/a\u003e\u003c\/b\u003e\u003cbr\u003eIf your ebike has Bosch Smart system with rim magnet, you would need \u003cb\u003e\u003ca href=\"https:\/\/www.twowheelsempire.com\/products\/speedbox-1-2-b-tuning-for-bosch-smart-system-rim-magnet\"\u003eSpeedBox 1.2 B.Tuning for Bosch (Smart System + Rim Magnet)\u003c\/a\u003e\u003c\/b\u003e or \u003cb\u003e\u003ca href=\"https:\/\/www.twowheelsempire.com\/collections\/all\/products\/speedbox-1-2-for-bosch-smart-system-rim-magnet\"\u003e SpeedBox 1.2 for Bosch (Smart System + Rim Magnet)\u003c\/a\u003e\u003c\/b\u003e\u003c\/p\u003e\n\u003ch3\u003eHow to install this Tuning kit?\u003c\/h3\u003e\n\u003cp\u003eWe use original connectors for the production of SpeedBox chips ensuring that the installation process is very simple and the chip is connected properly. We have also prepared detailed instructions and videos to make installation easy for you. Disassembly of the tuning chip is just as easy. If you have any troubles with installation or disassembly, do not hesitate to contact us. \u003cbr\u003e\u003cbr\u003eIf you are planning to install SpeedBox on a brand-new bike, make sure you ride it for at least 1 km before the chip is activated. \u003cbr\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cdiv class=\"text-center\"\u003e\n\u003cb\u003eImportant:\u003c\/b\u003e\u003cbr\u003eConnect the male - female connectors in the direction of the lock. Do not rotate the connectors during connection! \u003cbr\u003e\u003cbr\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0051\/1515\/0434\/files\/speedbox-connection.png?v=1670584224\" alt=\"\"\u003e\n\u003c\/div\u003e\n\u003cp\u003e\u003cbr\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp class=\"text-center fw-bold\"\u003eInstallation Guide:\u003c\/p\u003e\n\u003cdiv style=\"padding-bottom: 56.25%; position: relative; display: block; width: 100%;\"\u003e\u003ciframe width=\"100%\" height=\"100%\" src=\"https:\/\/www.youtube.com\/embed\/eaerAdy2P7o?si=dD2Q7r9VlRuA43CH\" style=\"position: absolute; top: 0; left: 0;\"\u003e\n    \u003c\/iframe\u003e\u003c\/div\u003e\n\u003ch3\u003eImportant legal note!\u003c\/h3\u003e\n\u003cp\u003ePlease note that the operation of this type of modified electric bikes on public roads may be against the law in some countries. The manufacturer takes no responsibility for damages resulting from the use SpeedBox products. Electric bikes equipped with SpeedBox products are not allowed to be used on public roads, cycling paths and public places. Electric bikes equipped with SpeedBox products can be used exclusively on private property and entirely at one’s own risk. \u003cbr\u003e\u003cbr\u003eThe use of SpeedBox may void the warranty of your ebike. \u003cbr\u003e\u003cbr\u003eWe strongly recommend using other safety features and protective gear to prevent injuries in higher speeds. \u003cbr\u003e\u003cbr\u003eSpeedBox Products are thoroughly tested and we stand by their quality. SpeedBox provide Life Long warranty to all their Products! \u003cbr\u003e\u003cbr\u003eIf You have any questions, please do not hesitate to contact us. Thank you for looking! Two Wheels Empire Team\u003c\/p\u003e","brand":"Speedbox","offers":[{"title":"Default Title","offer_id":39730917900422,"sku":"SB11_BT_SS","price":269.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0051\/1515\/0434\/files\/speedbox-1-1-b-tuning-for-bosch-smart-system-sb11-bt-ss-1145467220.jpg?v=1741936375"},{"product_id":"peartune-mso-for-bosch-smart-system-e-bike-e-mtb-tuning-kit","title":"PearTune MSO 4.0 for Bosch Smart System e-Bike e-MTB Tuning kit","description":"\u003ch3\u003eWhat does this Tuning Kit do?\u003c\/h3\u003e\n\u003cp\u003ePeartune tuning kit removes the 16mph (25km\/h) speed limit, allowing the motor to help you at higher speeds. With the speed limit removed, 28-37mph (~45-60km\/h) can be expected, depending on the bicycle and gearing. \u003cbr\u003e\u003cbr\u003eAfter exceeding 16mph (25km\/h) your actual speed is indicated on the last two digits of the display. This works with km\/h only. \u003cbr\u003e\u003cbr\u003eExample: \u003cbr\u003e- \u003cb\u003e22.3\u003c\/b\u003e corresponds to a speed of \u003cb\u003e23 km\/h\u003c\/b\u003e \u003cbr\u003e- \u003cb\u003e23.1\u003c\/b\u003e corresponds to a speed of \u003cb\u003e31 km\/h\u003c\/b\u003e \u003cbr\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003ch3\u003eHow does the Peartune work?\u003c\/h3\u003e\n\u003cp\u003eThe tuning kit manipulates the speed signal without altering the motor's power relative to pedaling speed. This guarantees a smooth motor control without speed limit interruptions. Depending on a tuning kit, some determine when assistance stops, while others remove the restriction entirely for continuous support. However, the achievable speed mostly depends on the eBike model. Achievable speed can be calculated using a simple formula: \u003cbr\u003e\u003cbr\u003eSpeed = Cadence [rpm] * Wheel circumference [mm] * Front Chainring Teeth \/ Rear Chainring Teeth * 60 [min\/h] \/ 1.000.000 [mm\/km] \u003cbr\u003e\u003cbr\u003eThe tuning kit can be activated directly on your bike’s display. After pressing the \u003cb\u003e'WALK' or '+ - + -' buttons\u003c\/b\u003e, from now on you will be able to ride at a speed of 25 mph (40 km\/h) and even up to 31 mph (50 km\/h)! \u003cbr\u003e\u003cbr\u003eTo deactivate the tuning kit, press the 'WALK' or '+ - + -' buttons again. Your e-bike will then work the same as before installation of the chip. \u003cbr\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp class=\"text-center fw-bold\"\u003eService menu video:\u003c\/p\u003e\n\u003cdiv style=\"padding-bottom: 56.25%; position: relative; display: block; width: 100%;\"\u003e\u003ciframe width=\"100%\" height=\"100%\" src=\"https:\/\/www.youtube.com\/embed\/mcyK7NXjML8\" style=\"position: absolute; top: 0; left: 0;\"\u003e\n    \u003c\/iframe\u003e\u003c\/div\u003e\n\u003cp\u003e\u003cbr\u003e\u003cbr\u003ePlease disable automatic updates in the eBike Flow App. And do not us flow app together with tuning kit.\u003c\/p\u003e\n\u003ch3\u003eHow to use Peartune Service Menu?\u003c\/h3\u003e\n\u003cp\u003eThe PearTune MSO 4.0 can be activated or deactivated anytime during the ride by short-pressing the LIGHT\/WALK button or [+ -] buttons. Original function of these buttons remains unchanged. After activating PearTune - you will be able to ride at a speed of 25 mph (40 km\/h), 31 mph (50 km\/h) and even more than 37 mph (60 km\/h)! \u003cbr\u003e\u003cbr\u003eSpecialized: Activation: ONE short press of WALK button and\/or [+ - + -] buttons, or [- + - +], or [+ + - -]or [- - + +] \/ (↑ ↓↑ ↓) buttons or ONE LONG press of + Indication: displayed number 9.9\/4.0 for few seconds after activation\/deactivation (or equivalent in miles) \u003cbr\u003e\u003cbr\u003eBosch: Activation: ONE short press of WALK button and\/or [+ - + -] buttons, or [- + - +], or [+ + - -]or [- - + +] \/ (↑ ↓↑ ↓) buttons Indication: displayed number 9.9\/2.5 for few seconds after activation\/deactivation (or equivalent in miles) \u003cbr\u003e\u003cbr\u003eBosch Smart System: Activation: ONE short press of WALK button and\/or [+ - + -] buttons, or [- + - +], or [+ + - -]or [- - + +] Indication: displayed number around 19.0\/12.0 for few seconds after activation\/deactivation (or equivalent in miles) \u003cbr\u003e\u003cbr\u003eBrose: Activation: ONE short press of LIGHT button or TWO short press of LIGHT button and\/or [+ - + -] buttons, or [- + - +], or [+ + - -]or [- - + +] \/ (↑ ↓↑ ↓) buttons Indication: displayed number 9.9\/2.5 for few seconds after activation\/deactivation (or equivalent in miles) \u003cbr\u003e\u003cbr\u003eGiant: Activation: ONE short press of WALK button and\/or [+ - + -] buttons, or [- + - +], or [+ + - -]or [- - + +] \/ (↑ ↓↑ ↓) buttons Indication: displayed number 9.9\/2.5 for few seconds after activation\/deactivation (or equivalent in miles) \u003cbr\u003e\u003cbr\u003eGiant Ridecontrol GO: Activation: ONE short press of WALK button and\/or [+ - + -] buttons, or [- + - +], or [+ + - -]or [- - + +] \/ (↑ ↓↑ ↓) buttons Indication: displayed number 9.9\/2.5 for few seconds after activation\/deactivation (or equivalent in miles) \u003cbr\u003e\u003cbr\u003eYamaha PW-X3 PW-S2: Activation: TWO short press of LIGHT button Indication: displayed number 9.9\/2.5 for few seconds after activation\/deactivation (or equivalent in miles) InterfaceX no indication, only if any App for Yamaha e-bikes avalaible\u2028\u2028Yamaha PW-X\/SE\/TE\/X2\/CE\/ST\u2028Activation: TWO short presses of the LIGHT button Indication: displayed number 9\/2 for few seconds after activation\/deactivation (or equivalent in miles) \u003cbr\u003e\u003cbr\u003eTQ Flyon: Activation: ONE short press of LIGHTS button and\/or [+ - + -] buttons, or [- + - +], or [+ + - -]or [- - + +] \/ (↑ ↓↑ ↓) buttons Indication: displayed number 9.9\/2.5 for few seconds after activation\/deactivation (or equivalent in miles) \u003cbr\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cdiv class=\"text-center\"\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0051\/1515\/0434\/files\/PearTune-MSO-manual-for-Service-menu-of-the-chip-Bosch-SMART_EN_87c7a41c-9265-42c6-b01e-fb172953d535.pdf?v=1718717632\" class=\"btn\" target=\"_blank\"\u003eService menu manual\u003c\/a\u003e\u003c\/div\u003e\n\u003ch3\u003eIs this Peartune the right tuning kit for my bike?\u003c\/h3\u003e\n\u003cp\u003eThe tuning chip for e-bikes with the newest Bosch Gen4 motor with Smart System. \u003cbr\u003e\u003cb\u003eCompatible with:\u003c\/b\u003e\u003cbr\u003e- displays KIOX 300, KIOX 300, PURION 200, INTUVIA 100 \u003cbr\u003e- motors Bosch Gen4 + Smart System - The module now supports drive unit software version up to 20.27.0\u003cbr\u003e\u003cbr\u003eNot compatible with e-bikes that have a magnet attached to a valve (Bosch Rim Magnet). \u003cbr\u003e\u003cbr\u003eNot compatible with with e-bikes with Bosch ABS system \u003cbr\u003e\u003cbr\u003eIf your e-bike has Bosch Gen4, Gen3 or Gen2 without Smart System, we recommend \u003cb\u003e\u003ca href=\"https:\/\/www.twowheelsempire.com\/products\/e-bike-e-mtb-tuning-kit-peartune-mso-3-0-for-bosch\" target=\"_blank\"\u003ePeartune 3.0 for Bosch (incl. Gen4)\u003c\/a\u003e\u003c\/b\u003e or \u003cb\u003e\u003ca href=\"https:\/\/www.twowheelsempire.com\/products\/e-bike-e-mtb-tuning-kit-peartune-4-0-for-bosch-not-smart-system\" target=\"_blank\"\u003ePeartune 4.0 for Bosch (incl. Gen4)\u003c\/a\u003e\u003c\/b\u003e\u003c\/p\u003e\n\u003ch3\u003eHow to install this Tuning kit?\u003c\/h3\u003e\n\u003cp\u003eWhen connecting Tuning Kit to an e-bike you will find connectors colored to make installation very simple. We have prepared detailed instructions and videos to make installation easy for you. Disassembly of our tuning kit is just as easy. If you have any troubles with installation or disassembly, do not hesitate to contact us. \u003cbr\u003e\u003cbr\u003eIf you are planning to install Peartune on a brand-new bike, make sure you ride it for at least 0.6 miles (1 km) before the tuning kit is activated. \u003cbr\u003e\u003c\/p\u003e\n\u003cdiv class=\"text-center\"\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0051\/1515\/0434\/files\/MANUAL_-_Bosch_Brose_Yamaha_Giant_Oli_Sachs_Bafang_M500_Specialized_with_original_connectors_EN.pdf?v=1671700645\" class=\"btn\" target=\"_blank\"\u003eInstallation Guide PDF\u003c\/a\u003e\u003c\/div\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp class=\"text-center fw-bold\"\u003eInstallation Guide:\u003c\/p\u003e\n\u003cp class=\"text-center\"\u003eATTENTION: If you wish to simply activate and use the tuning kit, follow the step 1 and step 4 of the video.\u003cbr\u003eIf you wish to see the closest possible speedometer value in KM\/h, follow the steps 1,2,3,4.\u003c\/p\u003e\n\u003cdiv style=\"padding-bottom: 56.25%; position: relative; display: block; width: 100%;\"\u003e\u003ciframe width=\"100%\" height=\"100%\" src=\"https:\/\/www.youtube.com\/embed\/-PIDzHCS5WM\" style=\"position: absolute; top: 0; left: 0;\"\u003e\n    \u003c\/iframe\u003e\u003c\/div\u003e\n\u003ch3\u003eImportant legal note!\u003c\/h3\u003e\n\u003cp\u003ePlease note that the operation of this type of modified electric bikes on public roads may be against the law in some countries. The manufacturer takes no responsibility for damages resulting from the use of Peartune products. Electric bikes equipped with Peartune products are not allowed to be used on public roads, cycling paths and public places. Electric bikes equipped with Peartune products can be used exclusively on private property and entirely at one’s own risk. The use of Peartune products may void the warranty of your ebike. \u003cbr\u003e\u003cbr\u003eWe strongly recommend using other safety features and protective gear to prevent injuries in higher speeds. \u003cbr\u003e\u003cbr\u003ePeartune products are thoroughly tested and we stand by their quality - Peartune provides Lifetime warranty to all their products.\u003c\/p\u003e","brand":"PearTune","offers":[{"title":"Default Title","offer_id":39778037727366,"sku":"PT-MSO-4.0-B2-SMART","price":239.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0051\/1515\/0434\/files\/peartune-mso-4-0-for-bosch-smart-system-e-bike-e-mtb-tuning-kit-pt-mso-4-0-b2-smart-1145465358.webp?v=1741936348"},{"product_id":"volspeed-tuning-kit-for-bosch-smart-system","title":"Volspeed Tuning kit for Bosch Smart System V2","description":"\u003ch3\u003eWhat does this Tuning Kit do?\u003c\/h3\u003e\n\u003cp\u003eTuning module for the Bosch Smart System. Compatible with all Bosch drive systems that are equipped with the Smart System and whose motor support ends at 25km\/h (15.5mph) from the factory. Note: Bikes with rim magnet are not supported\u003c\/p\u003e\n\u003ch3\u003eHow does Volspeed work?\u003c\/h3\u003e\n\u003cp\u003eThe tuning kit manipulates the speed signal without altering the motor's power relative to pedaling speed. This guarantees a smooth motor control without speed limit interruptions. Depending on a tuning kit, some determine when assistance stops, while others remove the restriction entirely for continuous support. However, the achievable speed mostly depends on the eBike model. Achievable speed can be calculated using a simple formula: \u003cbr\u003e\u003cbr\u003eSpeed = Cadence [rpm] * Wheel circumference [mm] * Front Chainring Teeth \/ Rear Chainring Teeth * 60 [min\/h] \/ 1.000.000 [mm\/km] \u003cbr\u003e\u003cbr\u003eThe tuning kit can be activated directly on your bike’s display, after pressing the ' - + - + ' buttons. After Tuning kit activation speed limit is displayed for 5 seconds. If you would like to change maximumm speed, just press '+' or '-' keys. Possible values: 16... 28mph (25... 45 km\/h). Default value: 20mph (32 km\/h). The set value is saved. \u003cbr\u003e\u003cbr\u003eTo deactivate the tuning kit, press the ' - + - + ' buttons. \u003cbr\u003e\u003cbr\u003eThe tuning is always switched off after switching on the bike. \u003cbr\u003e\u003cbr\u003eIt is possible to set a \"softer curtailment behavior\" (dynamic mode). This significantly softens the otherwise very abrupt deceleration at the speed limit. Correct display of the speed, the distance covered and the average speed at all times. \u003cbr\u003e\u003cbr\u003e\u003cb\u003eAttention: When tuning is activated, the speed displayed is too low from 21km\/h and the distance measured is too short. The odometer reading is therefore too low after using the tuning.\u003c\/b\u003e\u003cbr\u003e\u003cbr\u003ePlease disable automatic updates in the eBike Flow App. And do not us flow app together with tuning kit.\u003c\/p\u003e\n\u003ch3\u003eWhich Volspeed Tuning Kit do I need?\u003c\/h3\u003e\n\u003cp\u003eThis tuning kit is compatible with Bosch Smart System. Bikes equipped with a rim magnet are not supported by the tuning. Not compatible with with e-bikes with Bosch ABS system as well. \u003cbr\u003e\u003cbr\u003e\u003cb\u003eVolspeed V2:\u003c\/b\u003eThe Smart System is most easily identified by the Intuvia 100, Kiox 300 or Kiox 500 display type or control unit LED Remote, Purion 200 or the system controller. he tuning kit is compatible with Drive Unit Software versions up to 19.24.0 \u003cbr\u003e\u003cbr\u003eIt is recommended that you use the following selection guide to choose the appropriate tuning. \u003cbr\u003e\u003cbr\u003e\u003cimg src=\"https:\/\/www.twowheelsempire.com\/cdn\/shop\/files\/Auswahlhilfe_Bosch_V4_red_1024x1024.jpg?v=1728627761\" class=\"img-fluid\"\u003e\u003c\/p\u003e\n\u003ch3\u003eHow to install this Tuning kit?\u003c\/h3\u003e\n\u003cp\u003eWhen connecting Tuning Kit to an e-bike you will find connectors colored to make installation very simple. We have prepared detailed instructions to make installation easy for you. Disassembly of our tuning kit is just as easy. If you have any troubles with installation or disassembly, do not hesitate to contact us. If you are planning to install Volspeed on a brand-new bike, make sure you ride it for at least 0.6 miles (1 km) before the tuning kit is activated. \u003cbr\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cdiv class=\"text-center\"\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0051\/1515\/0434\/files\/V2_Smart_System_Operating_Instructions.pdf?v=1737543961\" class=\"btn\" target=\"_blank\"\u003eInstallation Guide PDF \u003c\/a\u003e\u003c\/div\u003e\n\u003cp\u003e\u003cbr\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp class=\"text-center fw-bold\"\u003eInstallation Guide:\u003c\/p\u003e\n\u003cdiv style=\"padding-bottom: 56.25%; position: relative; display: block; width: 100%;\"\u003e\u003ciframe width=\"100%\" height=\"100%\" src=\"https:\/\/www.youtube.com\/embed\/W3-WQZu4SwU?si=oNC-88PSzVVgO2mo\" style=\"position: absolute; top: 0; left: 0;\"\u003e\n    \u003c\/iframe\u003e\u003c\/div\u003e\n\u003ch3\u003eImportant legal note!\u003c\/h3\u003e\n\u003cp\u003ePlease note that the operation of this type of modified electric bikes on public roads may be against the law in some countries. The manufacturer takes no responsibility for damages resulting from the use VOLspeed products. Electric bikes equipped with VOLspeed products are not allowed to be used on public roads, cycling paths and public places. Electric bikes equipped with VOLspeed products can be used exclusively on private property and entirely at one’s own risk. The use of VOLspeed may void the warranty of your ebike. \u003cbr\u003e\u003cbr\u003eWe strongly recommend using other safety features and protective gear to prevent injuries in higher speeds. \u003cbr\u003eVOLspeed Products are thoroughly tested and we stand by their quality. VOLspeed provide 2 years warranty to all their Products!\u003c\/p\u003e","brand":"VOLspeed","offers":[{"title":"Volspeed V2","offer_id":40948889649286,"sku":"TWE-VS-SM-V2","price":199.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0051\/1515\/0434\/files\/volspeed-tuning-kit-for-bosch-smart-system-v2-twe-vs-sm-v2-1145465780.jpg?v=1741935947"},{"product_id":"speedbox-1-2-for-bosch-smart-system-rim-magnet","title":"SpeedBox 1.3 for Bosch Gen4 (Smart System + Rim Magnet)","description":"\u003ch3\u003eWhat does this Tuning Kit do?\u003c\/h3\u003e\n\u003cp\u003eSpeedBox 1.3 for Bosch is a tuning chip that removes the speed limiter on your e-bike. With this chip you can ride faster and enjoy the full potential of your Bosch motor.\u003c\/p\u003e\n\u003ch3\u003eHow does Speedbox work?\u003c\/h3\u003e\n\u003cp\u003eThe tuning kit manipulates the speed signal without altering the motor's power relative to pedaling speed. This guarantees a smooth motor control without speed limit interruptions. Depending on a tuning kit, some determine when assistance stops, while others remove the restriction entirely for continuous support. However, the achievable speed mostly depends on the eBike model. Achievable speed can be calculated using a simple formula: \u003cbr\u003e\u003cbr\u003eSpeed = Cadence [rpm] * Wheel circumference [mm] * Front Chainring Teeth \/ Rear Chainring Teeth * 60 [min\/h] \/ 1.000.000 [mm\/km] \u003cbr\u003e\u003cbr\u003eAfter installation, activate the chip via your e-bike’s control unit. Use the WALK assist function (short press of the “-” button). The display will show 3.5 km\/h (2.2 mph) and assistance will be unlocked up to 35 km\/h. You can set your own speed limit up to 99 km\/h, but we recommend not exceeding 35 km\/h to minimize the risk of error codes. \u003cbr\u003e\u003cbr\u003eTo deactivate the tuning, briefly activate WALK assist again (short press of the “-” button). Your e-bike display will show 2.5 km\/h (1.6 mph) and the speed limit will reset to 25 km\/h. Your e-bike will then work the same as before the tuning installation. \u003cbr\u003e\u003cbr\u003eSpeedBox also works on e-bikes without an enabled WALK assist function. In that case, you can activate\/deactivate tuning by switching between two assistance modes twice, i.e., pressing - + - +. \u003cbr\u003e\u003cbr\u003eYou can set the maximum speed limit by switching the modes from TURBO three levels down and then three levels up: eMTB - TOUR+ - ECO - TOUR+ - eMTB - TURBO. The current speed limit will then be displayed. The maximum assistance speed can also be switched by briefly activating WALK assist or by turning the rear wheel 360°. The value of 2.5 km\/h corresponds to a limit of 25 km\/h, 3.0 to 30 km\/h, 3.5 to 35 km\/h, etc. The last displayed limit will be saved after 15 seconds of inactivity. \u003cbr\u003e\u003cbr\u003eAfter finishing the ride, leave the bike on until a value of 0.0 km\/h is displayed. During this process the remaining time will be shown. Then it is safe to turn off your bike. Do not remove the display to lock the e-bike until SpeedBox finishes the countdown. \u003cbr\u003e\u003cbr\u003eActivate\/deactivate the tuning before the ride (when the e-bike is standing still), not during riding!\u003c\/p\u003e\n\u003ch3\u003eWhich Speedbox Tuning Kit do I need?\u003c\/h3\u003e\n\u003cp\u003eThis tuning kit is compatible with Bosch Smart System Gen4 Performance line CX, Performance line CX race, Performance Line Speed motors, BDU374Y, BDU376Y with Rim Magnet with the drive unit software versions up to 20.27.0.\u003c\/p\u003e\n\u003ch3\u003eHow to install this Tuning kit?\u003c\/h3\u003e\n\u003cp\u003eWhen connecting Tuning Kit to an e-bike you will find connectors colored to make installation very simple. We have prepared detailed instructions to make installation easy for you. Disassembly of our tuning kit is just as easy. If you have any troubles with installation or disassembly, do not hesitate to contact us. If you are planning to install Speedbox on a brand-new bike, make sure you ride it for at least 0.6 miles (1 km) before the tuning kit is activated. \u003cbr\u003e\u003c\/p\u003e\n\u003cp class=\"text-center fw-bold\"\u003eInstallation Guide:\u003c\/p\u003e\n\u003cdiv style=\"padding-bottom: 56.25%; position: relative; display: block; width: 100%;\"\u003e\u003ciframe width=\"100%\" height=\"100%\" src=\"https:\/\/www.youtube.com\/embed\/y8l87ksRUjM?si=xy6thDNEZpz34T57\" style=\"position: absolute; top: 0; left: 0;\"\u003e\n    \u003c\/iframe\u003e\u003c\/div\u003e\n\u003ch3\u003eImportant legal note!\u003c\/h3\u003e\n\u003cp\u003ePlease note that the operation of this type of modified electric bikes on public roads may be against the law in some countries. The manufacturer takes no responsibility for damages resulting from the use Speedbox products. Electric bikes equipped with Speedbox products are not allowed to be used on public roads, cycling paths and public places. Electric bikes equipped with Speedbox products can be used exclusively on private property and entirely at one’s own risk. The use of Speedbox may void the warranty of your ebike. \u003cbr\u003e\u003cbr\u003eWe strongly recommend using other safety features and protective gear to prevent injuries in higher speeds. \u003cbr\u003eSpeedbox Products are thoroughly tested and we stand by their quality. Speedbox provide 2 years warranty to all their Products!\u003c\/p\u003e","brand":"Speedbox","offers":[{"title":"Default Title","offer_id":40376012177542,"sku":"SB13_B","price":349.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0051\/1515\/0434\/files\/7ea3ac3006bc1fbaa5817737e8b00d6b-sb13-b.jpg?v=1761286774"},{"product_id":"speedfun-furious-evo-easy-for-bosch-smart-system","title":"SpeedFun Furious Evo easy+ for Bosch Smart System","description":"\u003ch3\u003eWhat does this Tuning Kit do?\u003c\/h3\u003e\n\u003cp\u003eTuning module for the Bosch Smart System. Compatible with all Bosch drive systems that are equipped with the Smart System and whose motor support ends at 25km\/h (15.5mph) from the factory. Note: Bikes with rim magnet and ABS systems are not supported\u003c\/p\u003e\n\u003ch3\u003eHow does Speedfun work?\u003c\/h3\u003e\n\u003cp\u003eThe tuning kit manipulates the speed signal without altering the motor's power relative to pedaling speed. This guarantees a smooth motor control without speed limit interruptions. Depending on a tuning kit, some determine when assistance stops, while others remove the restriction entirely for continuous support. However, the achievable speed mostly depends on the eBike model. Achievable speed can be calculated using a simple formula: \u003cbr\u003e\u003cbr\u003eSpeed = Cadence [rpm] * Wheel circumference [mm] * Front Chainring Teeth \/ Rear Chainring Teeth * 60 [min\/h] \/ 1.000.000 [mm\/km] \u003cbr\u003e\u003cbr\u003e\u003cb\u003eNote:\u003c\/b\u003e\u003cbr\u003e- It is supplied ready to use in \"ALWAYS ON\" mode and cannot be deactivated.\u003cbr\u003e- If you want to be able to activate and deactivate the speed release function, you need to cut\/interrupt the jumper at the point indicated by the arrow (insulate both ends!). There is no way back after this. Read the activation and deactivation methods on the instructions.\u003cbr\u003e\u003cbr\u003e\u003cb\u003eActivation:\u003c\/b\u003e\u003cbr\u003e- Turn Off the ebike.\u003cbr\u003e- Place the chain on the longest gear (the smallest rear sprocket).\u003cbr\u003e- Position the left pedal at 11:00. From now on, do not turn the rear wheel.\u003cbr\u003e- Turn On the ebike and wait for the complete check. Don't spin the rear wheel (not yet ..).\u003cbr\u003e- Raise the rear wheel, give a strong pedal. Let the wheel spin over 30 km\/h for a few seconds.\u003cbr\u003eThe system recognizes the acceleration and considers it as a command to activate or deactivate (cyclically) the speed release. Upon activation, the display (if present) shows the speed that passes from real to manipulated in the manner described above. When deactivated, the display shows the speed change from manipulated to real and the bike returns to its original condition. \u003cbr\u003e\u003cbr\u003ePlease disable automatic updates in the eBike Flow App. And do not us flow app together with tuning kit.\u003c\/p\u003e\n\u003ch3\u003eIs this the tuning kit that I need?\u003c\/h3\u003e\n\u003cp\u003eThis tuning kit is compatible with Bosch Smart System. Bikes equipped with a rim magnet are not supported by the tuning. Not compatible with with e-bikes with Bosch ABS system as well. This device is not compatible with ebikes equipped with a GPS system (Bosch ConnectModule). The Smart System is most easily identified by the Intuvia 100 or Kiox 300 display type or the LED Remote control unit or the system controller.\u003c\/p\u003e\n\u003ch3\u003eHow to install this Tuning kit?\u003c\/h3\u003e\n\u003cp\u003eWhen connecting Tuning Kit to an e-bike you will find connectors colored to make installation very simple. We have prepared detailed instructions to make installation easy for you. Disassembly of our tuning kit is just as easy. If you have any troubles with installation or disassembly, do not hesitate to contact us. If you are planning to install Speedfun on a brand-new bike, make sure you ride it for at least 0.6 miles (1 km) before the tuning kit is activated. \u003cbr\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cdiv class=\"text-center\"\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0051\/1515\/0434\/files\/Istruzioni-FURIOUS-EVO-EASY-Bosch-Smart-System-IT-EN-FR_compressed.pdf?v=1709728451\" class=\"btn\" target=\"_blank\"\u003eInstallation Guide PDF \u003c\/a\u003e\u003c\/div\u003e\n\u003cp\u003e\u003cbr\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp class=\"text-center fw-bold\"\u003eInstallation Guide:\u003c\/p\u003e\n\u003cdiv style=\"padding-bottom: 56.25%; position: relative; display: block; width: 100%;\"\u003e\u003ciframe width=\"100%\" height=\"100%\" src=\"https:\/\/www.youtube.com\/embed\/H8xueWHvrSg?si=D-ONmXpt0_zFuGSV\" style=\"position: absolute; top: 0; left: 0;\"\u003e\n    \u003c\/iframe\u003e\u003c\/div\u003e\n\u003ch3\u003eImportant legal note!\u003c\/h3\u003e\n\u003cp\u003ePlease note that the operation of this type of modified electric bikes on public roads may be against the law in some countries. The manufacturer takes no responsibility for damages resulting from the use Speedfun products. Electric bikes equipped with Speedfun products are not allowed to be used on public roads, cycling paths and public places. Electric bikes equipped with Speedfun products can be used exclusively on private property and entirely at one’s own risk. The use of Speedfun may void the warranty of your ebike. \u003cbr\u003e\u003cbr\u003eWe strongly recommend using other safety features and protective gear to prevent injuries in higher speeds. \u003cbr\u003eSpeedfun Products are thoroughly tested and we stand by their quality. Speedfun provide 1 year warranty to all their Products!\u003c\/p\u003e","brand":"SpeedFun","offers":[{"title":"Default Title","offer_id":40638888345734,"sku":"TWE-SF-B-SM","price":149.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0051\/1515\/0434\/files\/speedfun-furious-evo-easy-for-bosch-smart-system-twe-sf-b-sm-1145465351.jpg?v=1741935722"},{"product_id":"speedfun-furious-evo-easy-for-bosch-smart-system-with-rim-magnet","title":"SpeedFun Furious Evo easy+ for Bosch Performance Line CX, Race CX (gen. 4) Smart System with Rim Magnet","description":"\u003ch3\u003eWhat does this Tuning Kit do?\u003c\/h3\u003e\nSpeedFun Furious Evo easy + is a tuning for ebike equipped with a Bosch Smart System motor that allows you to remove the 25 km\/h speed block.\n\u003cbr\u003e\u003cbr\u003e\nThis speed release device is compatible only and exclusively with Bosch Performance Line CX (Gen 4 BES3) motors equipped with a magnet on the valve (Bosch Rim Magnet) regardless of the display or handlebar control.\n\u003cbr\u003e\u003cbr\u003e\nThis speed release device is compatible only and exclusively with Bosch Performance Line CX and Performance Line CX Race Limited Edition (gen.4 BES3) motors equipped with a magnet on the valve (Bosch Rim Magnet) with LED Remote\/System Controller command (also compatible with Led Remote + Kiox 300\/500, Intuvia 100, Purion 400 or System Controller + Mini Remote) or Purion 200.\n\n\u003ch3\u003eHow does Speedfun work?\u003c\/h3\u003e\nThe tuning kit manipulates the speed signal without altering the motor's power relative to pedaling speed. This guarantees a smooth motor control without speed limit interruptions. Depending on a tuning kit, some determine when assistance stops, while others remove the restriction entirely for continuous support. However, the achievable speed mostly depends on the eBike model. Achievable speed can be calculated using a simple formula: \u003cbr\u003e\u003cbr\u003e\n\nSpeed = Cadence [rpm] * Wheel circumference [mm] * Front Chainring Teeth \/ Rear Chainring Teeth * 60 [min\/h] \/ 1.000.000 [mm\/km]\n\u003cbr\u003e\u003cbr\u003e\n\u003cb\u003eNote:\u003c\/b\u003e\u003cbr\u003e- It is supplied ready to use in \"ALWAYS ON\" mode and cannot be deactivated.\u003cbr\u003e\n- If you want to be able to activate and deactivate the speed release function, you need to cut\/interrupt the jumper at the point indicated by the arrow (insulate both ends!). There is no way back after this. Read the activation and deactivation methods on the instructions.\u003cbr\u003e\u003cbr\u003e\n\u003cb\u003eActivation:\u003c\/b\u003e\u003cbr\u003e\n- Turn Off the ebike.\u003cbr\u003e\n- Place the chain on the longest gear (the smallest rear sprocket).\u003cbr\u003e\n- Position the left pedal at 11:00. From now on, do not turn the rear wheel.\u003cbr\u003e\n- Turn On the ebike and wait for the complete check. Don't spin the rear wheel (not yet ..).\u003cbr\u003e\n- Raise the rear wheel, give a strong pedal. Let the wheel spin over 30 km\/h for a few seconds.\u003cbr\u003e\nThe system recognizes the acceleration and considers it as a command to activate or deactivate (cyclically) the speed release. Upon activation, the display (if present) shows the speed that passes from real to manipulated in the manner described above. When deactivated, the display shows the speed change from manipulated to real and the bike returns to its original condition.\n\n\u003ch3\u003eIs this the tuning kit that I need?\u003c\/h3\u003e\nThis speed release device is compatible only and exclusively with Bosch Performance Line CX and Performance Line CX Race Limited Edition (gen.4 BES3) motors equipped with a magnet on the valve (Bosch Rim Magnet) with LED Remote\/System Controller command (also compatible with Led Remote + Kiox 300\/500, Intuvia 100, Purion 400 or System Controller + Mini Remote) or Purion 200. \u003cb\u003eBosch Gen4 motor codes start with BDU37**\u003c\/b\u003e If your eBike has no Rim Magnet, then you need to choose a different product. This device is not compatible with ebikes equipped with a GPS system (Bosch ConnectModule).\n\n\u003ch3\u003eHow to install this Tuning kit?\u003c\/h3\u003e\nWhen connecting Tuning Kit to an e-bike you will find connectors colored to make installation very simple. We have prepared detailed instructions to make installation easy for you. Disassembly of our tuning kit is just as easy. If you have any troubles with installation or disassembly, do not hesitate to contact us.\nIf you are planning to install Speedfun on a brand-new bike, make sure you ride it for at least 0.6 miles (1 km) before the tuning kit is activated.\n\u003cbr\u003e\u003cbr\u003e\n\u003cdiv class=\"text-center\"\u003e\n\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0051\/1515\/0434\/files\/Istruzioni-FURIOUS-EVO-EASY-BOSCH-RIM-MAGNET-IT-EN-FR_compressed.pdf?v=1728299608\" class=\"btn\" target=\"_blank\"\u003eInstallation Guide PDF \u003c\/a\u003e \u003c\/div\u003e\n\n\u003ch3\u003eImportant legal note!\u003c\/h3\u003e\nPlease note that the operation of this type of modified electric bikes on public roads may be against the law in some countries. The manufacturer takes no responsibility for damages resulting from the use Speedfun products. Electric bikes equipped with Speedfun products are not allowed to be used on public roads, cycling paths and public places. Electric bikes equipped with Speedfun  products can be used exclusively on private property and entirely at one’s own risk. The use of Speedfun may void the warranty of your ebike.\n\u003cbr\u003e\u003cbr\u003e\nWe strongly recommend using other safety features and protective gear to prevent injuries in higher speeds.\n\u003cbr\u003e\nSpeedfun Products are thoroughly tested and we stand by their quality. \nSpeedfun provide 1 year warranty to all their Products!","brand":"SpeedFun","offers":[{"title":"Default Title","offer_id":53525392884086,"sku":"TWE-SF-B-SM-RIM","price":249.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0051\/1515\/0434\/files\/speedfun-furious-evo-easy-for-bosch-performance-line-cx-gen-4-smart-system-with-rim-magnet-twe-sf-b-sm-rim-1145465792.jpg?v=1741935481"},{"product_id":"speedfun-furious-evo-easy-for-bosch-performance-line-cx-gen-5-smart-system-with-rim-magnet","title":"SpeedFun Furious Evo easy+ for Bosch Performance Line CX (gen. 5) Smart System with Rim Magnet","description":"\u003ch3\u003eWhat does this Tuning Kit do?\u003c\/h3\u003e\nSpeedFun Furious Evo easy + is a tuning for ebike equipped with a Bosch Smart System motor that allows you to remove the 25 km\/h speed block.\n\u003cbr\u003e\u003cbr\u003e\nThis speed release device is compatible only and exclusively with Bosch Performance Line CX (gen 5) motors equipped with a magnet on the valve (Bosch Rim Magnet) regardless of the display or handlebar control.\n\u003cbr\u003e\u003cbr\u003e\nThis speed release device is compatible only and exclusively with Bosch Performance Line CX (gen.5) motors equipped with a magnet on the valve (Bosch Rim Magnet) with LED Remote\/System Controller command (also compatible with Led Remote + Kiox 300\/500, Intuvia 100, Purion 400 or System Controller + Mini Remote) or Purion 200.\n\n\u003ch3\u003eHow does Speedfun work?\u003c\/h3\u003e\nThe tuning kit manipulates the speed signal without altering the motor's power relative to pedaling speed. This guarantees a smooth motor control without speed limit interruptions. Depending on a tuning kit, some determine when assistance stops, while others remove the restriction entirely for continuous support. However, the achievable speed mostly depends on the eBike model. Achievable speed can be calculated using a simple formula: \u003cbr\u003e\u003cbr\u003e\n\nSpeed = Cadence [rpm] * Wheel circumference [mm] * Front Chainring Teeth \/ Rear Chainring Teeth * 60 [min\/h] \/ 1.000.000 [mm\/km]\n\u003cbr\u003e\u003cbr\u003e\n\u003cb\u003eNote:\u003c\/b\u003e\u003cbr\u003e- It is supplied ready to use in \"ALWAYS ON\" mode and cannot be deactivated.\u003cbr\u003e\n- If you want to be able to activate and deactivate the speed release function, you need to cut\/interrupt the jumper at the point indicated by the arrow (insulate both ends!). There is no way back after this. Read the activation and deactivation methods on the instructions.\u003cbr\u003e\u003cbr\u003e\n\u003cb\u003eActivation:\u003c\/b\u003e\u003cbr\u003e\n- Turn Off the ebike.\u003cbr\u003e\n- Place the chain on the longest gear (the smallest rear sprocket).\u003cbr\u003e\n- Position the left pedal at 11:00. From now on, do not turn the rear wheel.\u003cbr\u003e\n- Turn On the ebike and wait for the complete check. Don't spin the rear wheel (not yet ..).\u003cbr\u003e\n- Raise the rear wheel, give a strong pedal. Let the wheel spin over 30 km\/h for a few seconds.\u003cbr\u003e\nThe system recognizes the acceleration and considers it as a command to activate or deactivate (cyclically) the speed release. Upon activation, the display (if present) shows the speed that passes from real to manipulated in the manner described above. When deactivated, the display shows the speed change from manipulated to real and the bike returns to its original condition.\n\n\u003ch3\u003eIs this the tuning kit that I need?\u003c\/h3\u003e\nThis speed release device is compatible only and exclusively with Bosch Performance Line CX (gen.5) motors equipped with a magnet on the valve (Bosch Rim Magnet) with LED Remote\/System Controller command (also compatible with Led Remote + Kiox 300\/500, Intuvia 100, Purion 400 or System Controller + Mini Remote) or Purion 200. \u003cb\u003eBosch Gen5 motor codes start with BDU38**\u003c\/b\u003e\n\u003cbr\u003e\u003cbr\u003e\nSpeedFun Furious Evo is supplied ready to use, plug and go, can be activated and deactivated at will and maintains the setting even after the ebike is turned off. It can be installed easily thanks to the compatible connectors. This device is not compatible with ebikes equipped with a GPS system (Bosch ConnectModule).\n\n\u003ch3\u003eHow to install this Tuning kit?\u003c\/h3\u003e\nWhen connecting Tuning Kit to an e-bike you will find connectors colored to make installation very simple. We have prepared detailed instructions to make installation easy for you. Disassembly of our tuning kit is just as easy. If you have any troubles with installation or disassembly, do not hesitate to contact us.\nIf you are planning to install Speedfun on a brand-new bike, make sure you ride it for at least 0.6 miles (1 km) before the tuning kit is activated.\n\u003cbr\u003e\u003cbr\u003e\n\u003cdiv class=\"text-center\"\u003e\n\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0051\/1515\/0434\/files\/Istruzioni-FURIOUS-EVO-EASY-BOSCH-RIM-MAGNET-CX-Gen-5-IT-EN-FR_compressed_20da4d8e-4a0c-4d8a-91ce-ef455695145c.pdf?v=1739253800\" class=\"btn\" target=\"_blank\"\u003eInstallation Guide PDF \u003c\/a\u003e \u003c\/div\u003e\n\n\u003ch3\u003eImportant legal note!\u003c\/h3\u003e\nPlease note that the operation of this type of modified electric bikes on public roads may be against the law in some countries. The manufacturer takes no responsibility for damages resulting from the use Speedfun products. Electric bikes equipped with Speedfun products are not allowed to be used on public roads, cycling paths and public places. Electric bikes equipped with Speedfun  products can be used exclusively on private property and entirely at one’s own risk. The use of Speedfun may void the warranty of your ebike.\n\u003cbr\u003e\u003cbr\u003e\nWe strongly recommend using other safety features and protective gear to prevent injuries in higher speeds.\n\u003cbr\u003e\nSpeedfun Products are thoroughly tested and we stand by their quality. \nSpeedfun provide 1 year warranty to all their Products!","brand":"SpeedFun","offers":[{"title":"Default Title","offer_id":54829517701494,"sku":"TWE-SF-B-SM-CX-GEN5-RIM","price":249.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0051\/1515\/0434\/files\/speedfun-furious-evo-easy-for-bosch-performance-line-cx-gen-4-smart-system-with-rim-magnet-twe-sf-b-sm-rim-1145465792.jpg?v=1741935481"},{"product_id":"speedfun-furious-evo-easy-for-bosch-performance-line-sx-gen-4-smart-system-with-rim-magnet","title":"SpeedFun Furious Evo easy+ for Bosch Performance Line SX (gen. 4) Smart System with Rim Magnet","description":"\u003ch3\u003eWhat does this Tuning Kit do?\u003c\/h3\u003e\nSpeedFun Furious Evo easy + is a tuning for ebike equipped with a Bosch Smart System motor that allows you to remove the 25 km\/h speed block.\n\u003cbr\u003e\u003cbr\u003e\nThis speed release device is compatible only and exclusively with Bosch Performance Line SX (gen.4) motors equipped with a magnet on the valve (Bosch Rim Magnet) with LED Remote\/System Controller command (also compatible with Led Remote + Kiox 300\/500, Intuvia 100, Purion 400 or System Controller + Mini Remote) or Purion 200.\n\n\u003ch3\u003eHow does Speedfun work?\u003c\/h3\u003e\nThe tuning kit manipulates the speed signal without altering the motor's power relative to pedaling speed. This guarantees a smooth motor control without speed limit interruptions. Depending on a tuning kit, some determine when assistance stops, while others remove the restriction entirely for continuous support. However, the achievable speed mostly depends on the eBike model. Achievable speed can be calculated using a simple formula: \u003cbr\u003e\u003cbr\u003e\n\nSpeed = Cadence [rpm] * Wheel circumference [mm] * Front Chainring Teeth \/ Rear Chainring Teeth * 60 [min\/h] \/ 1.000.000 [mm\/km]\n\u003cbr\u003e\u003cbr\u003e\n\u003cb\u003eNote:\u003c\/b\u003e\u003cbr\u003e- It is supplied ready to use in \"ALWAYS ON\" mode and cannot be deactivated.\u003cbr\u003e\n- If you want to be able to activate and deactivate the speed release function, you need to cut\/interrupt the jumper at the point indicated by the arrow (insulate both ends!). There is no way back after this. Read the activation and deactivation methods on the instructions.\u003cbr\u003e\u003cbr\u003e\n\u003cb\u003eActivation:\u003c\/b\u003e\u003cbr\u003e\n- Turn Off the ebike.\u003cbr\u003e\n- Place the chain on the longest gear (the smallest rear sprocket).\u003cbr\u003e\n- Position the left pedal at 11:00. From now on, do not turn the rear wheel.\u003cbr\u003e\n- Turn On the ebike and wait for the complete check. Don't spin the rear wheel (not yet ..).\u003cbr\u003e\n- Raise the rear wheel, give a strong pedal. Let the wheel spin over 30 km\/h for a few seconds.\u003cbr\u003e\nThe system recognizes the acceleration and considers it as a command to activate or deactivate (cyclically) the speed release. Upon activation, the display (if present) shows the speed that passes from real to manipulated in the manner described above. When deactivated, the display shows the speed change from manipulated to real and the bike returns to its original condition.\n\n\u003ch3\u003eIs this the tuning kit that I need?\u003c\/h3\u003e\nThis speed release device is compatible only and exclusively with Bosch Performance Line SX (gen.4) motors equipped with a magnet on the valve (Bosch Rim Magnet) with LED Remote\/System Controller command (also compatible with Led Remote + Kiox 300\/500, Intuvia 100, Purion 400 or System Controller + Mini Remote) or Purion 200.\u003cbr\u003e\u003cbr\u003e\n\u003cb\u003eATTENTION!\u003c\/b\u003e\u003cbr\u003e\nThis device is not compatible with ebikes equipped with a “classic” magnet on the spokes or brake disc. \u003cbr\u003e\nThis device is not compatible with ebikes equipped with the Bosch ABS system.\u003cbr\u003e\nThis device is not compatible with ebikes equipped with a GPS system (Bosch ConnectModule).\n\n\u003ch3\u003eHow to install this Tuning kit?\u003c\/h3\u003e\nWhen connecting Tuning Kit to an e-bike you will find connectors colored to make installation very simple. We have prepared detailed instructions to make installation easy for you. Disassembly of our tuning kit is just as easy. If you have any troubles with installation or disassembly, do not hesitate to contact us.\nIf you are planning to install Speedfun on a brand-new bike, make sure you ride it for at least 0.6 miles (1 km) before the tuning kit is activated.\n\u003cbr\u003e\u003cbr\u003e\n\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0051\/1515\/0434\/files\/Istruzioni-FURIOUS-EVO-EASY-BOSCH-RIM-MAGNET-SX-ALTO-IT-EN-FR_compressed.pdf?v=1732777646\" target=\"_blank\"\u003eInstallation instruction for motors with top attachments (BDU3142 and BDU3143) \u003c\/a\u003e\u003cbr\u003e\n\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0051\/1515\/0434\/files\/Istruzioni-FURIOUS-EVO-EASY-BOSCH-RIM-MAGNET-SX-DIAGONALE-IT-EN-FR_compressed.pdf?v=1732777739\" target=\"_blank\"\u003eInstallation and use instruction for motors with diagonal attachments (BDU3144 and BDU3145)\u003c\/a\u003e\n\n\u003ch3\u003eImportant legal note!\u003c\/h3\u003e\nPlease note that the operation of this type of modified electric bikes on public roads may be against the law in some countries. The manufacturer takes no responsibility for damages resulting from the use Speedfun products. Electric bikes equipped with Speedfun products are not allowed to be used on public roads, cycling paths and public places. Electric bikes equipped with Speedfun  products can be used exclusively on private property and entirely at one’s own risk. The use of Speedfun may void the warranty of your ebike.\n\u003cbr\u003e\u003cbr\u003e\nWe strongly recommend using other safety features and protective gear to prevent injuries in higher speeds.\n\u003cbr\u003e\nSpeedfun Products are thoroughly tested and we stand by their quality. \nSpeedfun provide 1 year warranty to all their Products!","brand":"SpeedFun","offers":[{"title":"BDU3142","offer_id":54830812561782,"sku":"TWE-SF-B-SM-SX-BDU3142-BDU3143-RIM","price":249.0,"currency_code":"EUR","in_stock":true},{"title":"BDU3143","offer_id":54830812594550,"sku":"TWE-SF-B-SM-SX-BDU3142-BDU3143-RIM-2","price":249.0,"currency_code":"EUR","in_stock":true},{"title":"BDU3144","offer_id":54830812627318,"sku":"TWE-SF-B-SM-SX-BDU3144-BDU3145-RIM","price":249.0,"currency_code":"EUR","in_stock":true},{"title":"BDU3145","offer_id":54830812660086,"sku":"TWE-SF-B-SM-SX-BDU3144-BDU3145-RIM-2","price":249.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0051\/1515\/0434\/files\/speedfun-furious-evo-easy-for-bosch-performance-line-cx-gen-4-smart-system-with-rim-magnet-twe-sf-b-sm-rim-1145465792.jpg?v=1741935481"},{"product_id":"speedfun-furious-evo-easy-for-bosch-performance-line-active-line-and-active-line-plus-gen-3-smart-system-with-rim-magnet","title":"SpeedFun Furious Evo easy+ for Bosch Performance Line, Active Line and Active Line Plus (gen. 3) Smart System with Rim Magnet","description":"\u003ch3\u003eWhat does this Tuning Kit do?\u003c\/h3\u003e\nSpeedFun Furious Evo easy + is a tuning for ebike equipped with a Bosch Smart System motor that allows you to remove the 25 km\/h speed block.\n\u003cbr\u003e\u003cbr\u003e\nThis speed release device is compatible only and exclusively with Bosch Performance Line, Active Line and Active Line Plus (gen. 3) motors equipped with a magnet on the valve (Bosch Rim Magnet) with LED Remote\/System Controller command (also compatible with Led Remote + Kiox 300\/500, Intuvia 100, Purion 400 or System Controller + Mini Remote) or Purion 200.\n\u003cbr\u003e\u003cbr\u003e\n\n\u003ch3\u003eHow does Speedfun work?\u003c\/h3\u003e\nThe tuning kit manipulates the speed signal without altering the motor's power relative to pedaling speed. This guarantees a smooth motor control without speed limit interruptions. Depending on a tuning kit, some determine when assistance stops, while others remove the restriction entirely for continuous support. However, the achievable speed mostly depends on the eBike model. Achievable speed can be calculated using a simple formula: \u003cbr\u003e\u003cbr\u003e\n\nSpeed = Cadence [rpm] * Wheel circumference [mm] * Front Chainring Teeth \/ Rear Chainring Teeth * 60 [min\/h] \/ 1.000.000 [mm\/km]\n\u003cbr\u003e\u003cbr\u003e\n\u003cb\u003eNote:\u003c\/b\u003e\u003cbr\u003e- It is supplied ready to use in \"ALWAYS ON\" mode and cannot be deactivated.\u003cbr\u003e\n- If you want to be able to activate and deactivate the speed release function, you need to cut\/interrupt the jumper at the point indicated by the arrow (insulate both ends!). There is no way back after this. Read the activation and deactivation methods on the instructions.\u003cbr\u003e\u003cbr\u003e\n\u003cb\u003eActivation:\u003c\/b\u003e\u003cbr\u003e\n- Turn Off the ebike.\u003cbr\u003e\n- Place the chain on the longest gear (the smallest rear sprocket).\u003cbr\u003e\n- Position the left pedal at 11:00. From now on, do not turn the rear wheel.\u003cbr\u003e\n- Turn On the ebike and wait for the complete check. Don't spin the rear wheel (not yet ..).\u003cbr\u003e\n- Raise the rear wheel, give a strong pedal. Let the wheel spin over 30 km\/h for a few seconds.\u003cbr\u003e\nThe system recognizes the acceleration and considers it as a command to activate or deactivate (cyclically) the speed release. Upon activation, the display (if present) shows the speed that passes from real to manipulated in the manner described above. When deactivated, the display shows the speed change from manipulated to real and the bike returns to its original condition.\n\n\u003ch3\u003eIs this the tuning kit that I need?\u003c\/h3\u003e\nThis speed release device is compatible only and exclusively with Bosch Performance Line, Active Line and Active Line Plus (gen. 3) motors equipped with a magnet on the valve (Bosch Rim Magnet) with LED Remote\/System Controller command (also compatible with Led Remote + Kiox 300\/500, Intuvia 100, Purion 400 or System Controller + Mini Remote) or Purion 200.\n\u003cbr\u003e\u003cbr\u003e\n\u003cb\u003eATTENTION!\u003c\/b\u003e\u003cbr\u003e\nThis device is not compatible with ebikes equipped with a “classic” magnet on the spokes or brake disc \u003cbr\u003e\nThis device is not compatible with ebikes equipped with the Bosch ABS system.\u003cbr\u003e\nThis device is not compatible with ebikes equipped with a GPS system (Bosch ConnectModule).\n\n\u003ch3\u003eHow to install this Tuning kit?\u003c\/h3\u003e\nWhen connecting Tuning Kit to an e-bike you will find connectors colored to make installation very simple. We have prepared detailed instructions to make installation easy for you. Disassembly of our tuning kit is just as easy. If you have any troubles with installation or disassembly, do not hesitate to contact us.\nIf you are planning to install Speedfun on a brand-new bike, make sure you ride it for at least 0.6 miles (1 km) before the tuning kit is activated.\n\u003cbr\u003e\u003cbr\u003e\n\u003cdiv class=\"text-center\"\u003e\n\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0051\/1515\/0434\/files\/Istruzioni-FURIOUS-EVO-EASY-BOSCH-RIM-MAGNET-Gen-3-IT-EN-FR_compressed.pdf?v=1750918391\" class=\"btn\" target=\"_blank\"\u003eInstallation Guide PDF \u003c\/a\u003e \u003c\/div\u003e\n\n\u003ch3\u003eImportant legal note!\u003c\/h3\u003e\nPlease note that the operation of this type of modified electric bikes on public roads may be against the law in some countries. The manufacturer takes no responsibility for damages resulting from the use Speedfun products. Electric bikes equipped with Speedfun products are not allowed to be used on public roads, cycling paths and public places. Electric bikes equipped with Speedfun  products can be used exclusively on private property and entirely at one’s own risk. The use of Speedfun may void the warranty of your ebike.\n\u003cbr\u003e\u003cbr\u003e\nWe strongly recommend using other safety features and protective gear to prevent injuries in higher speeds.\n\u003cbr\u003e\nSpeedfun Products are thoroughly tested and we stand by their quality. \nSpeedfun provide 1 year warranty to all their Products!","brand":"SpeedFun","offers":[{"title":"Default Title","offer_id":55828509720950,"sku":"TWE-SF-B-SM-GEN3-RIM","price":249.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0051\/1515\/0434\/files\/speedfun-furious-evo-easy-for-bosch-performance-line-cx-gen-4-smart-system-with-rim-magnet-twe-sf-b-sm-rim-1145465792.jpg?v=1741935481"},{"product_id":"volspeed-tuning-kit-for-bosch-smart-system-performance-line-cx-motor-with-rim-magnet","title":"Volspeed Tuning V2 kit for Bosch Smart System Performance Line CX (Gen4 and Gen5) motor with Rim Magnet","description":"\u003ch3\u003eWhat does this Tuning Kit do?\u003c\/h3\u003e\n\u003cp\u003eTuning module for Bosch Performance Line CX motor and a rim magnet ONLY. Important: This tuning only works with bikes that have a rim magnet. Models without a rim magnet are not supported. Supports Performance Line CX Gen4 (BDU37xx) and Gen5 (BDU38xx). Also Not compatible with Bosch ABS system.\u003c\/p\u003e\n\u003ch3\u003eHow does Volspeed work?\u003c\/h3\u003e\n\u003cp\u003eThe tuning kit manipulates the speed signal without altering the motor's power relative to pedaling speed. This guarantees a smooth motor control without speed limit interruptions. Depending on a tuning kit, some determine when assistance stops, while others remove the restriction entirely for continuous support. However, the achievable speed mostly depends on the eBike model. Achievable speed can be calculated using a simple formula: \u003cbr\u003e\u003cbr\u003eSpeed = Cadence [rpm] * Wheel circumference [mm] * Front Chainring Teeth \/ Rear Chainring Teeth * 60 [min\/h] \/ 1.000.000 [mm\/km] \u003cbr\u003e\u003cbr\u003eThe tuning kit can be activated directly on your bike’s display, after pressing the ' - + - + ' buttons. After Tuning kit activation speed limit is displayed for 5 seconds. If you would like to change maximumm speed, just press '+' or '-' keys. Possible values: 16... 28mph (25... 45 km\/h). Default value: 20mph (32 km\/h). The set value is saved. \u003cbr\u003e\u003cbr\u003eTo deactivate the tuning kit, press the ' - + - + ' buttons. \u003cbr\u003e\u003cbr\u003eThe tuning is always switched off after switching on the bike. \u003cbr\u003e\u003cbr\u003eIt is possible to set a \"softer curtailment behavior\" (dynamic mode). This significantly softens the otherwise very abrupt deceleration at the speed limit. Correct display of the speed, the distance covered and the average speed at all times. \u003cbr\u003e\u003cbr\u003e\u003cb\u003eAttention: When tuning is activated, the speed displayed is too low from 21km\/h and the distance measured is too short. The odometer reading is therefore too low after using the tuning.\u003c\/b\u003e\u003cbr\u003e\u003cbr\u003ePlease disable automatic updates in the eBike Flow App. And do not us flow app together with tuning kit.\u003c\/p\u003e\n\u003ch3\u003eWhich Volspeed Tuning Kit do I need?\u003c\/h3\u003e\n\u003cp\u003eThis tuning kit is compatible with Bosch Smart System Performance Line CX motor and a Rim Magnet. Not compatible with with e-bikes with Bosch ABS system as well. \u003cbr\u003e\u003cbr\u003e\u003cb\u003eVolspeed:\u003c\/b\u003eThe Smart System is most easily identified by the Intuvia 100, Kiox 300 or Kiox 500 display type or control unit LED Remote, Purion 200 or the system controller. \u003cbr\u003e\u003cbr\u003eCompatible with software versions up to 20.27.0\u003c\/p\u003e\n\u003ch3\u003eHow to install this Tuning kit?\u003c\/h3\u003e\n\u003cp\u003eWhen connecting Tuning Kit to an e-bike you will find connectors colored to make installation very simple. We have prepared detailed instructions to make installation easy for you. Disassembly of our tuning kit is just as easy. If you have any troubles with installation or disassembly, do not hesitate to contact us. If you are planning to install Volspeed on a brand-new bike, make sure you ride it for at least 0.6 miles (1 km) before the tuning kit is activated. \u003cbr\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cdiv class=\"text-center\"\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0051\/1515\/0434\/files\/1386_BA_E_VOLspeed_Bosch_Smart_Rim_Rev1.pdf?v=1753180772\" class=\"btn\" target=\"_blank\"\u003eInstallation Guide PDF English \u003c\/a\u003e\u003c\/div\u003e\n\u003cp\u003e\u003cbr\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cdiv class=\"text-center\"\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0051\/1515\/0434\/files\/1405_BA_E_VOLspeed_Bosch_Smart_Rim_V2_Rev0.pdf?v=1771312732\" class=\"btn\" target=\"_blank\"\u003eInstallation Guide PDF English\u003c\/a\u003e\u003c\/div\u003e\n\u003cp\u003e\u003cbr\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp class=\"text-center fw-bold\"\u003eInstallation Guide Performance Line CX Gen4 (BD37xx)\u003c\/p\u003e\n\u003cdiv style=\"padding-bottom: 56.25%; position: relative; display: block; width: 100%;\"\u003e\u003ciframe width=\"100%\" height=\"100%\" src=\"https:\/\/www.youtube.com\/embed\/zpMbjm_RN8w?si=XBFwcXWdf-4K-K6Q\" style=\"position: absolute; top: 0; left: 0;\"\u003e\n    \u003c\/iframe\u003e\u003c\/div\u003e\n\u003cp\u003e\u003cbr\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp class=\"text-center fw-bold\"\u003eInstallation Guide Performance Line CX Gen5 (BDU38xx)\u003c\/p\u003e\n\u003cdiv style=\"padding-bottom: 56.25%; position: relative; display: block; width: 100%;\"\u003e\u003ciframe width=\"100%\" height=\"100%\" src=\"https:\/\/www.youtube.com\/embed\/7lpoRP-ZXWA?si=x7jldqozrbiaqGH5\" style=\"position: absolute; top: 0; left: 0;\"\u003e\n    \u003c\/iframe\u003e\u003c\/div\u003e\n\u003ch3\u003eImportant legal note!\u003c\/h3\u003e\n\u003cp\u003ePlease note that the operation of this type of modified electric bikes on public roads may be against the law in some countries. The manufacturer takes no responsibility for damages resulting from the use VOLspeed products. Electric bikes equipped with VOLspeed products are not allowed to be used on public roads, cycling paths and public places. Electric bikes equipped with VOLspeed products can be used exclusively on private property and entirely at one’s own risk. The use of VOLspeed may void the warranty of your ebike. \u003cbr\u003e\u003cbr\u003eWe strongly recommend using other safety features and protective gear to prevent injuries in higher speeds. \u003cbr\u003eVOLspeed Products are thoroughly tested and we stand by their quality. VOLspeed provide 2 years warranty to all their Products!\u003c\/p\u003e","brand":"VOLspeed","offers":[{"title":"Default Title","offer_id":55975268647286,"sku":"TWE-VS-SM-RIM-V2","price":239.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0051\/1515\/0434\/files\/1386_VOLspeed_Bosch_CX_Rim_3000x2000_1.jpg?v=1753180105"},{"product_id":"speedbox-1-3-for-bosch-gen4-smart-system-rim-magnet","title":"SpeedBox 1.3 B.Tuning for Bosch Gen4 (Smart System + Rim Magnet)","description":"\u003ch3\u003eWhat does this Tuning Kit do?\u003c\/h3\u003e\n\u003cp\u003eSpeedBox 1.3 B.Tuning for Bosch is a tuning chip that removes the speed limiter on your e-bike. With this chip you can ride faster and enjoy the full potential of your Bosch motor. The actual speed and complete ride data are shown correctly in the SpeedBox App right on your phone.\u003c\/p\u003e\n\u003ch3\u003eHow does Speedbox work?\u003c\/h3\u003e\n\u003cp\u003eThe tuning kit manipulates the speed signal without altering the motor's power relative to pedaling speed. This guarantees a smooth motor control without speed limit interruptions. Depending on a tuning kit, some determine when assistance stops, while others remove the restriction entirely for continuous support. However, the achievable speed mostly depends on the eBike model. Achievable speed can be calculated using a simple formula: \u003cbr\u003e\u003cbr\u003eSpeed = Cadence [rpm] * Wheel circumference [mm] * Front Chainring Teeth \/ Rear Chainring Teeth * 60 [min\/h] \/ 1.000.000 [mm\/km] \u003cbr\u003e\u003cbr\u003eAfter installation, activate the chip via your e-bike’s control unit. Use the WALK assist function (short press of the “-” button). The display will show 3.5 km\/h (2.2 mph) and assistance will be unlocked up to 35 km\/h. You can set your own speed limit up to 99 km\/h, but we recommend not exceeding 35 km\/h to minimize the risk of error codes. \u003cbr\u003e\u003cbr\u003eTo deactivate the tuning, briefly activate WALK assist again (short press of the “-” button). Your e-bike display will show 2.5 km\/h (1.6 mph) and the speed limit will reset to 25 km\/h. Your e-bike will then work the same as before the tuning installation. \u003cbr\u003e\u003cbr\u003eSpeedBox also works on e-bikes without an enabled WALK assist function. In that case, you can activate\/deactivate tuning by switching between two assistance modes twice, i.e., pressing - + - +. \u003cbr\u003e\u003cbr\u003eYou can set the maximum speed limit by switching the modes from TURBO three levels down and then three levels up: eMTB - TOUR+ - ECO - TOUR+ - eMTB - TURBO. The current speed limit will then be displayed. The maximum assistance speed can also be switched by briefly activating WALK assist or by turning the rear wheel 360°. The value of 2.5 km\/h corresponds to a limit of 25 km\/h, 3.0 to 30 km\/h, 3.5 to 35 km\/h, etc. The last displayed limit will be saved after 15 seconds of inactivity. \u003cbr\u003e\u003cbr\u003eAfter finishing the ride, leave the bike on until a value of 0.0 km\/h is displayed. During this process the remaining time will be shown. Then it is safe to turn off your bike. Do not remove the display to lock the e-bike until SpeedBox finishes the countdown. \u003cbr\u003e\u003cbr\u003eActivate\/deactivate the tuning before the ride (when the e-bike is standing still), not during riding!\u003c\/p\u003e\n\u003ch3\u003eWhich Speedbox Tuning Kit do I need?\u003c\/h3\u003e\n\u003cp\u003eThis tuning kit is compatible with Bosch Smart System Gen4 Performance line CX, Performance line CX race, Performance Line Speed motors, BDU374Y, BDU376Y with Rim Magnet with the drive unit software versions up to 20.27.0.\u003c\/p\u003e\n\u003ch3\u003eHow to install this Tuning kit?\u003c\/h3\u003e\n\u003cp\u003eWhen connecting Tuning Kit to an e-bike you will find connectors colored to make installation very simple. We have prepared detailed instructions to make installation easy for you. Disassembly of our tuning kit is just as easy. If you have any troubles with installation or disassembly, do not hesitate to contact us. If you are planning to install Speedbox on a brand-new bike, make sure you ride it for at least 0.6 miles (1 km) before the tuning kit is activated.\u003cbr\u003e\u003c\/p\u003e\n\u003cp class=\"text-center fw-bold\"\u003eInstallation Guide:\u003c\/p\u003e\n\u003cdiv style=\"padding-bottom: 56.25%; position: relative; display: block; width: 100%;\"\u003e\u003ciframe width=\"100%\" height=\"100%\" src=\"https:\/\/www.youtube.com\/embed\/y8l87ksRUjM?si=xy6thDNEZpz34T57\" style=\"position: absolute; top: 0; left: 0;\"\u003e\n    \u003c\/iframe\u003e\u003c\/div\u003e\n\u003ch3\u003eImportant legal note!\u003c\/h3\u003e\n\u003cp\u003ePlease note that the operation of this type of modified electric bikes on public roads may be against the law in some countries. The manufacturer takes no responsibility for damages resulting from the use Speedbox products. Electric bikes equipped with Speedbox products are not allowed to be used on public roads, cycling paths and public places. Electric bikes equipped with Speedbox products can be used exclusively on private property and entirely at one’s own risk. The use of Speedbox may void the warranty of your ebike. \u003cbr\u003e\u003cbr\u003eWe strongly recommend using other safety features and protective gear to prevent injuries in higher speeds. \u003cbr\u003eSpeedbox Products are thoroughly tested and we stand by their quality. Speedbox provide 2 years warranty to all their Products!\u003c\/p\u003e","brand":"Speedbox","offers":[{"title":"Default Title","offer_id":56731946746230,"sku":"SB13BT_B","price":399.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0051\/1515\/0434\/files\/ca2789123cb6e2fc3bdae446a974a60c-sb13bt-b.jpg?v=1764051680"},{"product_id":"speedbox-1-6-for-bosch-smart-system-gen-5-rim-magnet","title":"SpeedBox 1.6 for Bosch (Smart System Gen.5 + Rim Magnet)","description":"\u003ch3\u003eWhat does this Tuning Kit do?\u003c\/h3\u003e\n\u003cp\u003eSpeedBox 1.6 for Bosch enables you to suppress the speed limiter on your e-bike. If you want to see correct speed and all riding data during your ride, we recommend choosing SpeedBox 1.6 B.Tuning for Bosch - you can see the real values in our SpeedBox App – right on the display of your phone.\u003c\/p\u003e\n\u003ch3\u003eHow does Speedbox work?\u003c\/h3\u003e\n\u003cp\u003eThe tuning kit manipulates the speed signal without altering the motor's power relative to pedaling speed. This guarantees a smooth motor control without speed limit interruptions. Depending on a tuning kit, some determine when assistance stops, while others remove the restriction entirely for continuous support. However, the achievable speed mostly depends on the eBike model. Achievable speed can be calculated using a simple formula: \u003cbr\u003e\u003cbr\u003eSpeed = Cadence [rpm] * Wheel circumference [mm] * Front Chainring Teeth \/ Rear Chainring Teeth * 60 [min\/h] \/ 1.000.000 [mm\/km] \u003cbr\u003e\u003cbr\u003eTo activate all the functions of the SpeedBox correctly, it is necessary to enter the menu after the first switching on of the e-bike after the tuning installation and switch to the circumference of the wheel of your e-bike, if you have older firmware on your e-bike. \u003cbr\u003e\u003cbr\u003eActivate\/deactivate the tuning before the ride (when the e-bike is standing still), not during riding! \u003cbr\u003e\u003cbr\u003eYou will activate the SpeedBox 1.6 tuning directly on your e-bike’s control unit by activating the WALK assist function shortly (holding down the “-” button). Your e-bike display will show a value of 3.5 km\/h (2.2 mph) and from now on you will be able to ride up to 35 km\/h. You may change the default speed limit to any limit you want (up to 99 kph), however, to minimize the risk of error codes, we recommend not to exceed 35 km\/h. \u003cbr\u003e\u003cbr\u003eTo deactivate the tuning, activate the WALK assist function shortly again (by holding down the “-” button). Your e-bike display will show a value of 2.5 km\/h (1.6 mph) and the speed limit will be reset to 25 km\/h. Your e-bike will then work the same as before the tuning installation. \u003cbr\u003e\u003cbr\u003eSpeedBox was also designed for e-bikes that do not have the WALK assist function enabled, or activated. In this case, you can activate\/deactivate tuning by switching between two assistance modes twice, i.e. by pressing the - + - + buttons. \u003cbr\u003e\u003cbr\u003eYou can set the maximum speed limit by switching the modes from TURBO mode three levels down and then three levels up: eMTB - TOUR+ - ECO - TOUR+ - eMTB - TURBO. An actual speed limit will be displayed after that. The maximum speed of an electric assistance can be switched by activating WALK assist function shortly or by turning the rear wheel 360°. The value of 2.5 km\/h on the display corresponds with the limit of 25 km\/h, 3.0 corresponds with 30 km\/h, 3.5 corresponds with 35 km\/h etc. The last displayed limit will be saved after 15 seconds of inactivity. \u003cbr\u003e\u003cbr\u003eAfter finishing the ride, leave the bike on until a value of 0.0 km\/h is displayed. During this process the remaining time will be displayed. Then it is safe to turn off your bike and you can start looking forward to your next trip. Do not remove the display to lock the e-bike until SpeedBox finishes the \"countdown\" process.\u003c\/p\u003e\n\u003ch3\u003eWhich Speedbox Tuning Kit do I need?\u003c\/h3\u003e\n\u003cp\u003eThis tuning kit is compatible with Bosch Smart System Gen5 Performance line CX (motor mounted with 2 bolts) with BDU38** motor code with Rim Magnet with the drive unit software versions up to 20.27.0.\u003c\/p\u003e\n\u003ch3\u003eHow to install this Tuning kit?\u003c\/h3\u003e\n\u003cp\u003eWhen connecting Tuning Kit to an e-bike you will find connectors colored to make installation very simple. We have prepared detailed instructions to make installation easy for you. Disassembly of our tuning kit is just as easy. If you have any troubles with installation or disassembly, do not hesitate to contact us. If you are planning to install Speedbox on a brand-new bike, make sure you ride it for at least 0.6 miles (1 km) before the tuning kit is activated. \u003cbr\u003e\u003c\/p\u003e\n\u003cp class=\"text-center fw-bold\"\u003eInstallation Guide:\u003c\/p\u003e\n\u003cdiv style=\"padding-bottom: 56.25%; position: relative; display: block; width: 100%;\"\u003e\u003ciframe width=\"100%\" height=\"100%\" src=\"https:\/\/www.youtube.com\/embed\/y0fTXfoPCsw?si=u-DvF91WN3injiHK\" style=\"position: absolute; top: 0; left: 0;\"\u003e\n    \u003c\/iframe\u003e\u003c\/div\u003e\n\u003ch3\u003eImportant legal note!\u003c\/h3\u003e\n\u003cp\u003ePlease note that the operation of this type of modified electric bikes on public roads may be against the law in some countries. The manufacturer takes no responsibility for damages resulting from the use Speedbox products. Electric bikes equipped with Speedbox products are not allowed to be used on public roads, cycling paths and public places. Electric bikes equipped with Speedbox products can be used exclusively on private property and entirely at one’s own risk. The use of Speedbox may void the warranty of your ebike. \u003cbr\u003e\u003cbr\u003eWe strongly recommend using other safety features and protective gear to prevent injuries in higher speeds. \u003cbr\u003eSpeedbox Products are thoroughly tested and we stand by their quality. Speedbox provide 2 years warranty to all their Products!\u003c\/p\u003e","brand":"Speedbox","offers":[{"title":"Default Title","offer_id":56731963064694,"sku":"SB16_B","price":349.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0051\/1515\/0434\/files\/4824291bd4e4b434b59bea0d41187dcf-sb16-b.jpg?v=1764052586"},{"product_id":"speedbox-1-6-b-tuning-for-bosch-smart-system-gen-5-rim-magnet","title":"SpeedBox 1.6 B.Tuning for Bosch (Smart System Gen.5 + Rim Magnet)","description":"\u003ch3\u003eWhat does this Tuning Kit do?\u003c\/h3\u003e\n\u003cp\u003eEnjoy your unlimited ride and all the great functions that our SpeedBox App has to offer. SpeedBox 1.6 B.Tuning for Bosch brings a unique connection of e-bike and mobile phone and suppresses the speed limiter on your e-bike. \u003cbr\u003eThe actual speed and other riding data will be displayed correctly in our SpeedBox App - right on the display of your phone.\u003c\/p\u003e\n\u003ch3\u003eHow does Speedbox work?\u003c\/h3\u003e\n\u003cp\u003eThe tuning kit manipulates the speed signal without altering the motor's power relative to pedaling speed. This guarantees a smooth motor control without speed limit interruptions. Depending on a tuning kit, some determine when assistance stops, while others remove the restriction entirely for continuous support. However, the achievable speed mostly depends on the eBike model. Achievable speed can be calculated using a simple formula: \u003cbr\u003e\u003cbr\u003eSpeed = Cadence [rpm] * Wheel circumference [mm] * Front Chainring Teeth \/ Rear Chainring Teeth * 60 [min\/h] \/ 1.000.000 [mm\/km] \u003cbr\u003e\u003cbr\u003eTo activate all the functions of the SpeedBox correctly, it is necessary to enter the menu after the first switching on of the e-bike after the tuning installation and switch to the circumference of the wheel of your e-bike, if you have older firmware on your e-bike. \u003cbr\u003e\u003cbr\u003eActivate\/deactivate the tuning before the ride (when the e-bike is standing still), not during riding! \u003cbr\u003e\u003cbr\u003eYou will activate the SpeedBox 1.6 tuning directly on your e-bike’s control unit by activating the WALK assist function shortly (holding down the “-” button). Your e-bike display will show a value of 3.5 km\/h (2.2 mph) and from now on you will be able to ride up to 35 km\/h. You may change the default speed limit to any limit you want (up to 99 kph), however, to minimize the risk of error codes, we recommend not to exceed 35 km\/h. \u003cbr\u003e\u003cbr\u003eTo deactivate the tuning, activate the WALK assist function shortly again (by holding down the “-” button). Your e-bike display will show a value of 2.5 km\/h (1.6 mph) and the speed limit will be reset to 25 km\/h. Your e-bike will then work the same as before the tuning installation. \u003cbr\u003e\u003cbr\u003eSpeedBox was also designed for e-bikes that do not have the WALK assist function enabled, or activated. In this case, you can activate\/deactivate tuning by switching between two assistance modes twice, i.e. by pressing the - + - + buttons. \u003cbr\u003e\u003cbr\u003eYou can set the maximum speed limit by switching the modes from TURBO mode three levels down and then three levels up: eMTB - TOUR+ - ECO - TOUR+ - eMTB - TURBO. An actual speed limit will be displayed after that. The maximum speed of an electric assistance can be switched by activating WALK assist function shortly or by turning the rear wheel 360°. The value of 2.5 km\/h on the display corresponds with the limit of 25 km\/h, 3.0 corresponds with 30 km\/h, 3.5 corresponds with 35 km\/h etc. The last displayed limit will be saved after 15 seconds of inactivity. \u003cbr\u003e\u003cbr\u003eAfter finishing the ride, leave the bike on until a value of 0.0 km\/h is displayed. During this process the remaining time will be displayed. Then it is safe to turn off your bike and you can start looking forward to your next trip. Do not remove the display to lock the e-bike until SpeedBox finishes the \"countdown\" process.\u003c\/p\u003e\n\u003ch3\u003eWhich Speedbox Tuning Kit do I need?\u003c\/h3\u003e\n\u003cp\u003eThis tuning kit is compatible with Bosch Smart System Gen5 Performance line CX (motor mounted with 2 bolts) with BDU38** motor code with Rim Magnet with the drive unit software versions up to 20.27.0.\u003c\/p\u003e\n\u003ch3\u003eHow to install this Tuning kit?\u003c\/h3\u003e\n\u003cp\u003eWhen connecting Tuning Kit to an e-bike you will find connectors colored to make installation very simple. We have prepared detailed instructions to make installation easy for you. Disassembly of our tuning kit is just as easy. If you have any troubles with installation or disassembly, do not hesitate to contact us. If you are planning to install Speedbox on a brand-new bike, make sure you ride it for at least 0.6 miles (1 km) before the tuning kit is activated. \u003cbr\u003e\u003c\/p\u003e\n\u003cp class=\"text-center fw-bold\"\u003eInstallation Guide:\u003c\/p\u003e\n\u003cdiv style=\"padding-bottom: 56.25%; position: relative; display: block; width: 100%;\"\u003e\u003ciframe width=\"100%\" height=\"100%\" src=\"https:\/\/www.youtube.com\/embed\/y0fTXfoPCsw?si=u-DvF91WN3injiHK\" style=\"position: absolute; top: 0; left: 0;\"\u003e\n    \u003c\/iframe\u003e\u003c\/div\u003e\n\u003ch3\u003eImportant legal note!\u003c\/h3\u003e\n\u003cp\u003ePlease note that the operation of this type of modified electric bikes on public roads may be against the law in some countries. The manufacturer takes no responsibility for damages resulting from the use Speedbox products. Electric bikes equipped with Speedbox products are not allowed to be used on public roads, cycling paths and public places. Electric bikes equipped with Speedbox products can be used exclusively on private property and entirely at one’s own risk. The use of Speedbox may void the warranty of your ebike. \u003cbr\u003e\u003cbr\u003eWe strongly recommend using other safety features and protective gear to prevent injuries in higher speeds. \u003cbr\u003eSpeedbox Products are thoroughly tested and we stand by their quality. Speedbox provide 2 years warranty to all their Products!\u003c\/p\u003e","brand":"Speedbox","offers":[{"title":"Default Title","offer_id":56732212363638,"sku":"SB16BT_B","price":399.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0051\/1515\/0434\/files\/2f87414e31ac07fc5019c84092bf8cf5-sb16bt-b.jpg?v=1764054255"}],"url":"https:\/\/www.twowheelsempire.com\/en-lt\/collections\/bosch-smart-system-e-bike-tuning-kits.oembed","provider":"Two Wheels Empire","version":"1.0","type":"link"}