SpeedFun Furious Evo for Ananda M60 M81 M100 M230 and Atala AM80 Agile (Gen. 2) motors

The function of the Furious Evo tuning device for Ananda M60 M81 M100 M230 and Atala AM80 Agile (Gen. 2) is to electronically manipulate the rotation speed of the rear wheel and to communicate to the motor a speed always lower than 25 KmH in order to obtain a very high real speed with the motor active. The maximum speed limit will therefore be dictated by the power of the motor added to the power expressed by your legs.

The tuning kit manipulates the speed signal without altering the motor's power relative to pedaling speed. This guarantees a smooth motor control without speed limit interruptions. Depending on a tuning kit, some determine when assistance stops, while others remove the restriction entirely for continuous support. However, the achievable speed mostly depends on the eBike model. Achievable speed can be calculated using a simple formula:

Speed = Cadence [rpm] * Wheel circumference [mm] * Front Chainring Teeth / Rear Chainring Teeth * 60 [min/h] / 1.000.000 [mm/km]

IMPORTANT Activation and deactivation:
- Turn the ebike off and on again. Do not move it or do other operations.
- Raise the rear wheel, give a strong pedal with the longest (hardest) gear engaged. Let it run for a few seconds.
- The system recognizes the acceleration and considers it as an activation or deactivation command (cyclically). Upon activation, the display shows the speed that change from real to halved in the manner described above. When deactivated, the display shows the speed change from halved to real and the bike returns to its original state.

SpeedFun Furious Evo can be activated and deactivated at will and maintains the setting even after the ebike is turned off. It can be installed on ebikes with Ananda M60 M81 M100 M230 and Atala AM80 Agile (Gen. 2) motors mounted mostly on Olympia ebikes (in this case often with the wording “Tuned by Olympia”) regardless of the type of display or side control of the ebike.

Compatible with:
Motors:
- Ananda M60 M81 M100 M230
- Atala AM80 Agile (Gen. 2)

Not Compatible with: This device is not compatible with Atala AM80 Agile (Gen. 1) motor. The product compatible with Atala AM80 Agile (Gen. 1) motor is available HERE

E-bikes with Ananda M60 M81 M100 M230 and Atala AM80 Agile (Gen. 2) motors where the Furious Evo device was successfully installed:
Ananda M100 tuned by Olympia
– Olympia EX 900 and EX 900 Prime
– Olympia Performer 900 and Performer 900 Prime
– Olympia Mistral 900

Ananda M81 tuned by Olympia (100Nm)
– Olympia EX 900 Trail
– Olympia Master 630 29″ or Master 630 26″
– Olympia Explorer 630
– Olympia Super Magnum man and Super Magnum comfort

Other ebikes M60 M81 M100 M230
– Nakamura Crossover XV
– Puch E-Modern N7

When connecting the SpeedFun chip to an eBike you will find connectors colored to make installation very simple. We have prepared detailed instructions and videos to make installation easy for you. Disassembly of our tuning chip is just as easy. If you have any troubles with installation or disassembly, do not hesitate to contact us.

Please note that the operation of this type of modified electric bikes on public roads may be against the law in some countries. The manufacturer takes no responsibility for damages resulting from the use SpeedFun products. Electric bikes equipped with SpeedFun products are not allowed to be used on public roads, cycling paths and public places. Electric bikes equipped with SpeedFun products can be used exclusively on private property and entirely at one’s own risk.

The use of SpeedFun may void the warranty of your ebike. We strongly recommend using other safety features and protective gear to prevent injuries in higher speeds.

Warranty does not cover damage resulting from eBike software updates. Remove the tuning kit before updating the software. Check with us first to ensure the kit is compatible with your updated eBike. We cannot guarantee that the kit will function the same after updates. Please exercise caution.